Classifieds RSS Feed

S13 Ca Seats + Swap Cusco Brace

Thu, 17 May 2012 06:57:13 +0000

1x standard s13 ca passenger seat + 1x brown trim s13 ca drivers seat. Drivers side has slight corner wear near the door and is also missing the bolt that holds the seat belt arm on. Overall both in great condition.

-$50

Also I'm looking for an s13 ca factory nissan/nismo strut brace. The one with the big bend over the plenum. Happy to swap my cusco brace if anyone is interested.

Seat pick up from Geelong.

Pignose 180sx Conversion.

Thu, 17 May 2012 06:56:13 +0000

hey all,

I recently sold my s13 silvia which I had purchased and fixed up some 180sx guards, bonnet, headlights and front bar. with intentions of making a onevia.

As I now don't own an S-chassis, I need to sell my front end conversion. perfect for someone wanting to make a onevia or wanting new, good condition panels for their 180.
the bonnet, guards and headlight covers are all in base primer, I've repaired any cracks and splits in the guards and now just needs to be sanded and painted!
the front bar is a plastic pignose front bar which I purchased brand new.

I'm hoping to sell as a complete conversion, if it doesn't sell within a month, I'll part the front out

$750 and comes with everything.
contact leigh on 0418-221-075.
cheers

2x Rays TE37 (17x10JJ+18) Matte Black

Thu, 17 May 2012 06:49:38 +0000

Ok time to let go of this pair as I need funds to upgrade

As per subject line, I'm selling 2x Rays TE37 (17x10JJ+18) in Matte Black. Note these have been a discontinued size for many many years now so you can't get them brand new anymore!!!

These rims were originally Bronze, although the colour has been perfectly matched to the optional Rays Matte Black by Wheel Solutions in Richmond, as they were done to match my front Rays optional Matte Black pair (which I'm keeping). Check here for pictures of the process ---> http://nissansilvia....l=&fromsearch=1

The condition of the rims are immaculate. No gutter rashing whatsoever and no buckles. Basically brand new condition, although there is a couple of very small stone chips on the lip of the rims, as you would normally get being rims for the rear.

I'll let the pictures do the talking, but note that they were taken just before they were fitted. But stressing again, current condition is pretty much the same. As you'll see in one of the pictures below that I have even gone to anal lengths to remove and replace the spec stickers showing the size etc.

I'm after $1.5k with rubber. I paid premium $$$ to get them done up by Wheel Solutions so I'm losing out big time. Again, keep in mind these are a discontinued size so you'll find them up for sale 2nd hand once in a blue moon if you're lucky.

Tyres are Potenza Adrenalins RE001 235/45R17 with about 90% rubber.

Genuine interest only. Also prefer cash only as I'm needing them for my next pair of rims. Unless you have 18x10.5J+22 or 18x10.5J+15 I ain't swapping

Note that the contact number is listed above in the "Display phone number" but you need to read it upside down hahahaha

Cheers,

Andy

NSW SYD: '89 Ti Nissan R31 Skyline, 270rwkW RB25DET

Thu, 17 May 2012 05:31:57 +0000

Legit reason for sale: This is my 5th 31 and definitely the best I have owned. I just want something different - something low and slow. This is low but definitely not slow. I just want something different and that is it.

Make: Nissan R31 Skyline Series 3 Ti Stormy glow colour

Kilometres: Odo reads 320,000 I think. Stopped a while ago.

Engine: RB25DET

Transmission: RB25DET five-speed manual, hugely heavy clutch, 4.11:1 locked diff.

Modifications:
RB25DET, high-mount china turbo rebuilt by CGC to GT35 specs (have receipts)
Turbosmart 44mm external gate
One month old full 3in exhaust system, over diff, new muffler, quiet as. Screamer pipe with a section that can be plumbed in/taken out.
Intercooler mounted up high with the radiator - cannot see this from the front. Full stealth mode.
Apexi Power FC
GReddy electronic boost controller; 15psi hi, 12psi lo, 10psi off

Have dyno-read outs. 270rwkW on 15psi. The latest one (a month or so before I had bought it) was in the afternoon at a dyno-day with the workshop admitting their dyno reads low and made 253rwkW on 15psi.

Will be getting it tuned again very soon by Uni Group Engineering.

Emotion coilovers all round - 12kg F/10kg R
HR31 (import) brakes and hubs up front
Minispool with 4.11:1 final drive ratio
Ti Skyline stockies with new Kumho tyres all round

Standard interior with full electrics, minus an aftermarket steering wheel. CD player and two subs in boot.

Roadworthy cert: Can be arranged

Rego: End of Sept '12, will be sold with.

Other comments:
Heaps of other things. Car is fantastic to drive. Exterior has a couple faults - I had a drift incident a while ago, so the bonnet is slightly dented and the grill cracked. I have a new grill. I am waiting for my guitar to sell, and am getting the entire car resprayed. This can be done before a trade, or without. Either way.

I run the car on 12psi all day every day. I have done two drift events in it, and was fantastic all day every day. Except when a cooler pipe blew, but oh well. That was fixed, obviously.

I have a lot of pics, so PM me if you are interested. Is a tidy car overall, and will suit someone who wants to go sideways at a million Ks an hour. I drive the car every day.

Registered until September this year. Is NOT engineered in NSW, but it is in QLD. I am keen to drive up for the right car.

Price is $6,500 ONO. Can do less without rego/without wheels/etcetc

Please ONLY CONTACT me if you have cash piled up and 100% want to view or are interested in the car. Don't ask me for a price if you have six bucks to spend. I am keen to work out a deal.

The car will NOT be sold with teh SSRs unless some sort of deal is made; they are Mike's and they also happen to be up for sale. So you can buy the car and the meshies. Otherwise, it will come with Ti wheels and 16x8 and 16x10 wedge-style steelies.

Contact me on either todd@hot4s.com.au or 0401 198 992.

Cheers!
[color=rgb(140, 188, 233)][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size][/color]

[color=rgb(140, 188, 233)][/size] (SAU Texikhana. Come on, everyone has a go of their cars!)[/color]

18" SSR "Premium Agle" Wheels

Thu, 17 May 2012 04:37:08 +0000

FS 18" SSR wheels

[indent]SSR "Premium Agle" Wheels
Flush fitment on JZA80's (with suplied spacers)

Front: 18 x 8.5 +43 / 235/45/18 (85~%)
Rear: 18 x 9.5 +43 / 265/35/18 (85~%)
2x 15mm rear Project Kics hub-centric spacers
2x 25mm rear Project Kics hub-centric spacers

Location: Woolongong
Pictured: All pics are WITH spacers on
Reason: need money to fund my motor and i have 2 sets

Price: $1250 firm is want i paid and i know it is an awesome deal[/indent][indent]Price includes almost new 265 and 235 tires

pm me or msg me on 0413829486

cheers stuart[/indent][indent]Located in woolongong[/indent]

FS - R32 Bonnet, R32 Guards, R32 Doors,

Thu, 17 May 2012 04:12:01 +0000

Hi Guys.

Decided to get rid of our R32 and concentrate on our other cars. So selling parts

R32 Front Guards $200 for the pair ono
R32 Bonnet $150 good condition needs painting.
R32 Silver doors $200 for the pair (come with glass)

As were pulling it apart to scrap we also have some random r32 parts forsale. pm me your requests

Can also paint the above to match your car if required.

Pickup is in West Footscray

sms 0415693273

thanks

Neil

Project NA 4.0 P Plater Legal SR20DE Silvia

Thu, 17 May 2012 04:11:51 +0000

Hi Guys.
The car is now complete and ready to go to a new home. Below are the details of the car it is P Plater Legal.

Nissan Silvia 1993

Suzuki Blue
SR20DE
Short Intake
Pod Filter
MSPEC S14 52mm Alloy Radiator
Performance Spark Leads
NPower Strut Brace Front
NPower Strut Brace Rear
Sports exhaust with Canon Muffler
Alloy Over Flow Container
Tein Drift Spec Type HE Winding Master Coilovers
CST Procedo Demon Cambers (Resprayed centers Suzuki Gold) 16x8 +/- 0 all round Advan 205/50/15, Toyo 205/55/15
Zebra Print Carpet and Glovebox
Genuine Silvia Floor Matts
Dished Steering Wheel with Nismo Horn
Drift Button (not installed)
Nismo Slat Grill
R200 Locked 4.3ratio Diff
Windows Tinted
Mongoose Alarm with Remote Central Locking
New Wiper Arms
Motor Just serviced
Front Main seal replaced engine has no leaks

Car looks and goes just as well. It also comes with a Bucket seat on a rail ready for the track and a Standard steering wheel.

Price drop to $6800 ono(and willing to take a further $200 off for interstate buyers to go towards shipping costs). Does not come with Rego/RWC.

Can lower the price by removing wheels but would prefer to sell as a package. Can be shipped interstate also (happy to work out a deal) PM or SMS/Call 0415693273. Previous Registration Plate was QGM-955 Car has cancelled registration, Nothing Oweing, Below are the pics of the car.

18 Inch Tyres

Thu, 17 May 2012 03:50:36 +0000

Have 2 set of 18 inch tyres

First set nankangs 225/40 18's x 2 stll have few mm of tread left $50 each

2nd set are Bridgestone 275/35 18's though are worn down to markers, good for burnouts drifting etc $30 the pair

Located in Carlton Sydney

Tks

Daniel.

Few Sets Of 17inch Wheels And Tyres For Sale

Thu, 17 May 2012 03:47:06 +0000

Have a few sets of wheels looking to offload, held onto them to use on track have since sold my car so dont really need them

17 x 8 inch wheels 3 only tyres still ok $100 for the 3

Also have a few 16 and 18 inch tyres here do cheap from $10 as need space

I am in Carlton in sydney for pick up
Can freight wheels if need be
Tks
Daniel.

F.S Nissan Navara 2010 ST Dual Cab 24 Inch Wheels

Thu, 17 May 2012 03:45:23 +0000

2010 Nissan Navara ST dual cab 4x4

2.5 litre diesel 5 speed manual

Only 22,000 just serviced

Now has standard navara wheels and new tyres

ARB canopy and ute liner fitted

November 2012 rego (plates not included)

Runs great and looks really good

Bluetooth for phone on steering wheel

air conditioned

heavy duty towbar

power steering

Still has new car warranty I have owned car from brand new

Only selling as need van for work which i have so rarely gets driven these days

Not going to give car away though if doesnt sell for close to what i want will keep it

Great for towing or going away

No longer has 24's

$330500 open to reasonable offers

In Sydney

Tks

Daniel.

Ford Trader Dual Cab Tilt Tray Tow Truck

Thu, 17 May 2012 03:43:05 +0000

Selling my tow truck as no longer use it

Its a 1985 Ford Trader dual cab

Has tilt tray with ramps

4 cylinder diesel 5 speed very economical was better than my gas falcon ute with car trailer

Has around 350k mark

2 new tyres about 12months ago very little use on them, along with king pins being done same time

Has heavy duty winch

4965 GVM

Also has a towbar

was registered in NSW now out not hard to get done as had lot work done last year for rego and has done probably 1000k's max since then

Does have some scrapes here and there and a door has rust bubble

Interior pretty clean and comfortable drive we used to do 6hr trips in it

CD player

Asking $12,000 or best offer cost me $15,000 couple years ago

Photos when got it

In Sydney

Tks

Daniel.

Work Emotion KAI Rims And Tyres

Thu, 17 May 2012 03:42:52 +0000

Have a set Work Emotion KAI rims and tyres

5 x 114.3 17x7 and 17 x 8 offset 32 and 42

Rims in really good condition some minor scrapes here and there

Tyres are 215 ans 235's still good tread

Asking $1000 open to reasonable offers

Tks

Daniel.

Bucket Seat New Bride Copy

Thu, 17 May 2012 03:21:56 +0000

Bucket seat, new, haven't been used or installed.

Plastic back, very light.

Comes with seat rail, don't know what car it will fit.

Quick sale, $350.

Located in Wollongong NSW, Kevin 0432 673 692.

HKS SILENT HIGH POWER CATBACK EXHAUST MUFFLER SUBARU IMPREZA GRB

Thu, 17 May 2012 02:47:21 +0000

　 silent Hi-Power TYPE-H インプレッサ IMPREZA
インプレッサ IMPREZA( CBA-GRB) Code No. 31019-AF026

JASMA Number JQR300931364
Vehicle インプレッサ IMPREZA Model CBA-GRB Engine EJ20(TURBO) Model Year 07/10- Remarks Shape of muffler HP SC( silent Hi-Power TYPE-H) Main material S304(*2) Diameter of tip 94 L&R Diameter of center pipe 65(*3) Close noise level Stock L80 R80 HKS L90 R89 About road clearance(*4) Clearance 156mm Portion of the kit Main silencer Remarks

Remarks *1: About silencer shell type of Silent Hi-Power
TYPE-S/Oval silencer for noise reduction.
TYPE-H/Round silencer for performance.

*2: Main material in the component figure.
: SUS304/ High quality stainless steel. : SUH409/ Stainless steel commonly used for stock exhaust. *3: About center pipe
Diameter of center pipe is the portion that has the largest diameter. (Excluding silencer and tip.) It is the condition with stock suspension.

*4: Minimum road clearance between HKS muffler (Any parts included in the kit) and road surface. Therefore, it may be different from actual road clearance of the vehicle.
The data is basically the condition with stock suspension. However, please understand that some items have data with low down spring or ride height adjustable suspension kit.

Caution: Hook, bracket, stay may be changed without prior notice.

★ Exhaust noise level at idle.

HKS FULL DUAL MUFFLER CATBACK EXHAUST NISSAN Z33 350Z VQ35DET

Thu, 17 May 2012 02:47:14 +0000

^{FULL DUAL} ^{フェアレディZ FAIRLADY Z}
^{フェアレディZ FAIRLADY Z( CBA-Z33)} ^{Code No. 32009-AN002}

^{JASMA Number} ^03S01185
^Vehicle ^{フェアレディZ FAIRLADY Z} ^Model ^CBA-Z33 ^Engine ^VQ35HR ^{Model Year} ^07/02-08/11 ^Remarks ^{Shape of muffler} ^{DTi( FULL DUAL)} ^{Main material} ^S304(*2) ^{Diameter of tip} ^{110 L&R} ^{Diameter of center pipe} ^{60 x 2(*3)} ^{Close noise level} ^Stock ^HKS ⁸⁸ ^{About road clearance(*4)} ^Clearance ^116mm ^{Portion of the kit} ^{First center pipe} ^Remarks

^Remarks ^{Fits to "Roadster(HZ33)".

*1: About silencer shell type of Silent Hi-Power

TYPE-S/Oval silencer for noise reduction.

TYPE-H/Round silencer for performance.

*2: Main material in the component figure.}
^: ^{SUS304/ High quality stainless steel.} ^: ^{SUH409/ Stainless steel commonly used for stock exhaust.} ^{*3: About center pipe

Diameter of center pipe is the portion that has the largest diameter. (Excluding silencer and tip.) It is the condition with stock suspension.

*4: Minimum road clearance between HKS muffler (Any parts included in the kit) and road surface. Therefore, it may be different from actual road clearance of the vehicle.

The data is basically the condition with stock suspension. However, please understand that some items have data with low down spring or ride height adjustable suspension kit.

Caution: Hook, bracket, stay may be changed without prior notice.

★ Exhaust noise level at idle.}

HKS SILENT HIGH POWER CATBACK EXHAUST MITSIBISHI EVO 9 4G63 CT9A

Thu, 17 May 2012 02:47:07 +0000

ランサーエボリューション LANCER EVOLUTION( GH-CT9A(IX，IX MR)) Code No. 31019-AM008

JASMA Number 03S05861
Vehicle ランサーエボリューション LANCER EVOLUTION Model GH-CT9A(IX，IX MR) Engine 4G63(MIVEC TURBO) Model Year 05/03-07/09 Remarks Shape of muffler HP( silent Hi-Power TYPE-S) Main material S304(*2) Diameter of tip 120 Diameter of center pipe 75(*3) Close noise level Stock 87 HKS 93 About road clearance(*4) Clearance 122mm Portion of the kit Main pipe Remarks

Remarks *1: About silencer shell type of Silent Hi-Power
TYPE-S/Oval silencer for noise reduction.
TYPE-H/Round silencer for performance.

*2: Main material in the component figure.
: SUS304/ High quality stainless steel. : SUH409/ Stainless steel commonly used for stock exhaust. *3: About center pipe
Diameter of center pipe is the portion that has the largest diameter. (Excluding silencer and tip.) It is the condition with stock suspension.

*4: Minimum road clearance between HKS muffler (Any parts included in the kit) and road surface. Therefore, it may be different from actual road clearance of the vehicle.
The data is basically the condition with stock suspension. However, please understand that some items have data with low down spring or ride height adjustable suspension kit.

Caution: Hook, bracket, stay may be changed without prior notice.

★ Exhaust noise level at idle

HKS KANSAI SERVICE TOWER BAR NISSAN SKYLINE R32/33 GTR RB26 DETT

Thu, 17 May 2012 02:47:00 +0000

HKS Kansai have adopted the cross-section Tower Bar that is superior in hardness and Durability. The inside components of the shaft when compared to other products is around three times stronger

- Genuine Kansai Service Part
- Direct Fit
- Polished Finish

KTN003 BNR32
Nissan Skyline GT-R BNR32 RB26DETT Front
Skyline - R32 GTR - BNR32

KTN014 BNR33/34
Nissan Skyline GT-R BNCR33/BNR34 RB26DETT Front
Skyline - R33/34 GTR - BNCR33/BNR34

DEFI ADVANCE BF Boost Gauge WHITE/RED/ BLUE+ADV Control Unit Set

Thu, 17 May 2012 02:46:52 +0000

DEFI Link ADVANCE Meter BF Boost Gauge 2.0 WHITE + Control Unit Set

You are looking at a brand new boxed Defi-link Advance BF Turbo Boost Gauge (2.0kPa) with Defi-Link Advance Control Unit.

*NEW MODEL* Next generation gauge technology from Defi. Electronic gauge with 60mm black face and WHITE illumination.

High intensity Illumination with 5 brightness levels for maximum visibility day and night.
Micro-controlled stepping motor provides instantaneous response and highly accurate measurements.
2 Variations of opening and closing modes.
Gauges can be controlled from distance with included switching system

Up to 7 Defi Advance BF/CR gauges can be linked together in a daisy-chain and controlled by a single control unit.

Set Includes :

Defi-link ADVANCE BF Boost Gauge 2.0kPa (Blue)
Defi-link ADVANCE Control Unit
Sensor, wiring and fittings
Mounting cup and stand
Instruction manual (English/Japanese)

** Defi-Link ADVANCE BF Gauges are not compatible with Defi-Link system gauges / Defi-Link Control Unit II.

Ducati 400SS Learner Legal

Thu, 17 May 2012 02:46:44 +0000

Hey all just an expression of interest.

Bike is a 1992 Ducati 400ss. Has 13,000k's on the clock. LAMS approved (learner legal), Mechanically A1, rides like a dream. Has twin after market carbon fibre pipes valued at $1500, which gives it that sweet big duke note. (sounds like a 900), Carbon fibre dash, 900SS mirrors, and a brand new rear tire.

This is a very cool bike to have as a learner.

The bike was Dyno tuned last year, so it runs alot smoother than most of the other ones you'l see around. I bought the bike a few months ago but I lost interest so it now lives in my dads garage and he gets to takes it for a spin every weekend.
Now for the fun part I dropped the bike about a month ago (low speed, rolling out of my driveway.. noobie mistake) So the panels are a lil scratched up. Left hand panel has 200 - 250 a crack in it near the indicator, right hand side has a few light grazes and 1 small crack. I have had a quote to get the panels repaired and resprayed by a reputable panel shop.

At the moment I kind of just want to cut my loses and move on, so Im willing to let go of the bike cheap in as is condition.
The going price for these bikes seem to be from $5500 - $6500 on the market. Id be happy to let the bike go for around the $5000 mark as is (reasonable offers considered) or for a fussy buyer I will book the panels in to get repaired and resprayed and Id be wanting $5900 firm for it.

Apart from the panel damage this bike would definitely be one of the better examples one the road, it is an absolute gem of a bike, and I really hate myself for doing such a stupid mistake. I guess one mans loss is another mans gain so hopefully the next owner will look after it better than I did.

Please no Low ball offers, and definatly NO trades. I just want cash. Test riders welcome providing a deposit is handed over before hand. Bike is located in the south east suburbs. Currently rego'd and rwc

If I get the money im asking i'l even throw in the brand new SHOEI helmet I bought, only used for about 4 rides, never dropped. Paid $600 for it.

HKS SILENT HIGH POWER CATBACK EXHAUST-NISSAN BNR34 GTR RB26DETT

Thu, 17 May 2012 02:46:21 +0000

スカイラインGT－R SKYLINE GT-R( GF-BNR34) Code No. 31019-AN013

JASMA Number 03S01416
Vehicle スカイラインGT－R SKYLINE GT-R Model GF-BNR34 Engine RB26DETT Model Year 99/01-02/08 Remarks Shape of muffler HP( silent Hi-Power TYPE-S) Main material S304(*2) Diameter of tip 120 Diameter of center pipe 85(*3) Close noise level Stock 95 HKS 93 About road clearance(*4) Clearance 95mm Portion of the kit Center silencer Remarks Data with height adjustable suspension kit.

Remarks For standard & V Spec. Not tested for V Spec II, M Spec.

*1: About silencer shell type of Silent Hi-Power
TYPE-S/Oval silencer for noise reduction.
TYPE-H/Round silencer for performance.

*2: Main material in the component figure.
: SUS304/ High quality stainless steel. : SUH409/ Stainless steel commonly used for stock exhaust. *3: About center pipe
Diameter of center pipe is the portion that has the largest diameter. (Excluding silencer and tip.) It is the condition with stock suspension.

*4: Minimum road clearance between HKS muffler (Any parts included in the kit) and road surface. Therefore, it may be different from actual road clearance of the vehicle.
The data is basically the condition with stock suspension. However, please understand that some items have data with low down spring or ride height adjustable suspension kit.

Caution: Hook, bracket, stay may be changed without prior notice.

★ Exhaust noise level at idle.

HKS STAINLESS CENTRE PIPE NISSAN 350Z Z33 FAIRLADY Z

Thu, 17 May 2012 02:46:13 +0000

For FAIRLADY Z, SKYLINE COUPE.

Larger diameter of pipes improves exhaust gas flow to muffler. Engine performance will be improved.
- Durable and good looking with SUS304.

Tomei Oversize Valve Nissan Skyline Rb26 R32 33 34 GTR

Thu, 17 May 2012 02:46:05 +0000

適合車種

IN/EX

Base
(mm)

Thickers
(mm)

length
(mm)

part number

RB26DETT
BNR32/BCNR33/BNR34 IN 35.65 5.97 102.3 163400 EX 31.15 6.94 101.6 SR20DET(R）
PS13/S14/S15 IN 35.15 5.97 101.4 163401 EX 31.15 6.94 102.4 4G63
EVO4～9 IN 35.00 6.57 109.6 163402 EX 31.50 6.54 109.6 EJ207/255
GDB C～G IN 37.00 5.96 103.85 163403 EX 33.00 5.96 104.2

please contact us or if you have any question!

0421622288 [24 hours]

e-mail sales-cjmotor@hotmail.com

or visit our website

www.cj-motor.com

Forced Performance Turbo Red BALL BEARING -Mit Evo 4-9-84mm Surg

Thu, 17 May 2012 02:45:57 +0000

Forced Performance is proud to announce the debut of our 100% brand new, patent pending, dual ceramic ball bearing design within the FP RED™ Turbocharger for the Lancer Evolution 4-9 vehicles. This new design virtually eliminates any limit to allowable thrust load within the turbocharger while simultaneously reducing drag and rotational resistance to spool up. The increased thrust limit significantly extends the longevity of the turbocharger when operated beyond its published flow and boost limits and eliminates the turbochargers sensitivity to lubrication interruptions due to hard acceleration and cornering forces. Recent performance testing at the MHI Research and Development Laboratories in Nagasaki, Japan verified that the design dramatically exceeds the normal allowable thrust loads for TD05/6 type turbochargers and allows for a significant increase in the available airflow from the turbocharger without bearing damage.
Internally very little is shared with any previously offered turbocharger anywhere in the world beyond the description of "ball bearing". This patent pending design is 100% blank page and will have an important impact on turbocharger bearing systems for years to come. The races and ceramic balls of the turbocharger are the highest grade components available anywhere, period.
From this point forward the standard journal bearing system will not be available for the FP RED™ Turbocharger for the Lancer Evolution 4-9.
Lancer Evolution 4-9 Ball Bearing Turbos and Upgrade Information

Information listed below is in regard to our original Journal Bearing FP RED™ Turbocharger. this turbo now includes our FP Evo Gen 2 Oil Supply Line. This turbo features a 12 month warranty. You must activate this warranty within 30 days of purchasing this turbocharger by returning the warranty card included with the turbocharger and a copy of your receipt if purchased from a supplier other than Forced Performance. Please contact us directly if you have any problems or questions regarding your turbocharger, disassembly of the turbocharger will void the warranty.
NEW to the FP RED™ for the Evolution IX Line up is our own custom 84mm Flow Advancement Port™ compressor cover. You can now choose the new FP 84mm Flow Advancement Port™cover or stick with the standard 64mm Stock Appearing compressor cover as shown above. The larger inlet configuration helps reduce huffing and surging sounds that are often reported with these larger stock format hybrids when lugging the engine at low RPM and high boost pressure but perhaps even more useful is the way it helps feed the splitter blades of the compressor wheel resulting in increased flow. This larger inlet also increases the volume of the intake air pipe and reduces vacuum at the inlet of the turbo. Additionally the volute of the cover is now exactly tailored to the HTA wheel aero for the best performance possible.
The 84mm inlet Flow Advancement Port™ version can be used with our Intake Air Pipe which is located in the Related Products section at the bottom of the page. The intake is undercover black and designed to replace the stock intake air pipe perfectly allowing the use of the recirculated BOV and the valve cover crankcase vent as in the OEM application. A non-recirculated version is also now available. The 84mm Flow Advancement Port™ cover can also be used with standard 3" air intake pipes by utilizing a straight 3" coupler also located in the Related Products section at the bottom of this page.

Forced Performance Turbo GREEN BALL BEARING -Mit Evo 4-9-84mm Su

Thu, 17 May 2012 02:45:50 +0000

Forced Performance is proud to announce the debut of our 100% brand new, patent pending, dual ceramic ball bearing design within the FP GREEN™ Turbocharger for the Lancer Evolution 4-9 vehicles. This new design virtually eliminates any limit to allowable thrust load within the turbocharger while simultaneously reducing drag and rotational resistance to spool up. The increased thrust limit significantly extends the longevity of the turbocharger when operated beyond its published flow and boost limits and eliminates the turbochargers sensitivity to lubrication interruptions due to hard acceleration and cornering forces. Recent performance testing at the MHI Research and Development Laboratories in Nagasaki, Japan verified that the design dramatically exceeds the normal allowable thrust loads for TD05/6 type turbochargers and allows for a significant increase in the available airflow from the turbocharger without bearing damage.
Internally very little is shared with any previously offered turbocharger anywhere in the world beyond the description of "ball bearing". This patent pending design is 100% blank page and will have an important impact on turbocharger bearing systems for years to come. The races and ceramic balls of the turbocharger are the highest grade components available anywhere, period.
Lancer Evolution 4-9 Ball Bearing Turbos and Upgrade Information
Curt Brown has put this turbo to the test for us and has posted an awesome 605whp backed up by a 602whp graph. This thing really is the ultimate street car turbo!

Forced Performance Turbo Ball Bearing EVO Black-Mitsibishi Evo X

Thu, 17 May 2012 02:45:41 +0000

Forced Performance is proud to announce the debut of our 100% brand new, patent pending, dual ceramic ball bearing design within the FP BLACK™ Turbocharger for the Lancer Evolution X vehicles. This new design virtually eliminates any limit to allowable thrust load within the turbocharger while simultaneously reducing drag and rotational resistance to spool up. The increased thrust limit significantly extends the longevity of the turbocharger when operated beyond its published flow and boost limits and eliminates the turbochargers sensitivity to lubrication interruptions due to hard acceleration and cornering forces. Recent performance testing at the MHI Research and Development Laboratories in Nagasaki, Japan verified that the design dramatically exceeds the normal allowable thrust loads for TD05/6 type turbochargers and allows for a significant increase in the available airflow from the turbocharger without bearing damage.
Internally very little is shared with any previously offered turbocharger anywhere in the world beyond the description of "ball bearing". This patent pending design is 100% blank page and will have an important impact on turbocharger bearing systems for years to come. The races and ceramic balls of the turbocharger are the highest grade components available anywhere, period.
From this point forward the standard journal bearing system will not be available for the FP BLACK™ Turbocharger for the Lancer Evolution X.

The FP BLACK™ for the Mitsubishi Lancer Evolution X is the most fully evolved stock appearing variant we offer. It features an 82mm HTA™ compressor wheel with a flow rate of 68lb/min. The turbine side features a large 67mm turbine wheel.
The turbo comes standard with an 18psi wastegate actuator and our FP Evo X High Flow Oil Supply Line and turbo oil filter. You may select a lower pressure actuator if needed, but the unit is intended to operate above 18psi of boost pressure. This turbocharger will produce 500-600whp results readily on well prepared engines.
This turbo is covered by our 12 month complimentary repair service. You must activate this service within 30 days of purchasing this turbocharger by returning the registration card included with the turbocharger and a copy of your receipt if purchased from a supplier other than Forced Performance. Please contact us directly if you have any problems or questions regarding your turbocharger, dis-assembly of the turbocharger or running an external wastegate will exclude the turbo from complimentary repair service.

VOLK RACING GT-C Face 2 Rims 17" 2 Peace Rims MAKE OFFER

Thu, 17 May 2012 02:25:50 +0000

Selling set

VOLK RACING GT-C Face 2 rims 17"

Light weight racing wheels 2 peace rims

Including centre caps

have removed off my S15 no longer needed clearing space

Fronts 17"- 7.5" (unshore on offset no sticker in rim)

Rears 17" - 8" +34 Offset

All very clean few small marks on centres from stone chips all very clean centre caps included

Tyres all round 80%- 90%

Rim can be delivered at buyers expence contact for quote

Delivery Sydney metro area

am located in Catherine fields near Narellan

Offers Accepted

Nissan S15 Spec B Eyelids MAKE OFFER

Thu, 17 May 2012 02:25:22 +0000

Selling set of S15 Spec B eyelids

bought a few months back never used collecting dust

can post contact for price

Black R34 Gtt open For Trade, Tdo6, Twin Waste Gate, External,

Thu, 17 May 2012 02:10:39 +0000

For sale is my
R34 GTT 1998
307rwKW @ 16-17PSI
Black

Engine:
RB25 NEO Det
TDO6 25G Turbo
Heat coated manifold and turbo exhaust
Custom dual waste gare system with screamer pipe
custom optimized intercooler pipeing
100mm thick core 600x400 intercooler inprove flow and heat exchange
Large forward facing throttle body
Forward facing inlet plenum cast polished all faces machined and honed inside
HKS fuel rail
1000cc injectors
Sard fuel pressure reg
Fuel dampener mod
All braided water and oil lines
Oil cooler
Power steering cooler
Battery relocation and Isolation switch fitted (ADR approved cables)
Full 3in exhaust system stainless steel with 5 in Cannon
heat wrapped external wastegate pipes and dump pipe to cat to keep head down
G ready oil catch can with custom return to sump

Full 3 bar mapsensor plug in ECU with boost controll, anti lag, launch controll etc, all options

Drive line:
Gearbox purchased from SAU OSGiken GTR gear sett
ORC high torque clutch it is hyper single or twin plate nice strong engagement with the twin plate idel sound\
The diff was shimmed to factory spec with 1.8mm shimm fitted by gearbox express in minto drives really well always lsd but not a locker very smooth

Suspension:
New OEM bushes
Bilstein coilover suspension
front adjustable strut brace

Exterior:
Rays engineering Racing Wheels
Carbon Spoiler Fin
Carbon pillar covers
Factory sports body kit

Interior:
Carbon centre console
Carbon Stereo surround
Blitz digital infometer, boost peak hoold , boost warning etc

This car has all the right gear and plenty of GO, with no wank factor, I would recomend this car to any one as it is very nice to drive, It has been tuned with a very safe tune and has plenty left in it if you desire, this set up can produce a 380rwKW figure with very good response.
The car is always serviced with MOTUL fluids and has never missed a beat.

The bad there is minor scratches which are hardly noticable and the speedo has recently stoped working i think that the plug jhas come off at the g box but i havent worried about it

pictures HERE http://www.skylinesa...-fpr-bosh-pump/

Plenty of rego left

Text me on 0450727488

I am open for trades..
My Reason for selling is that i have owned a r34 skyline all my life and would like a change, so i am open for trades for almost any car with the right adjustment your way or mine..

Defi Electonic Boost Gauge + Control Unit

Thu, 17 May 2012 02:03:48 +0000

Defi electectronic boost gauge + Control Unit

$250

Same as this one:

http://www.nengun.co...-unit-ii-195021

Pickup or can ship anywhere in Australia at buyers expense.

Give me a call/text/email if you have any questions. I don't come on here much.

Adam
0419577352
psyche126@hotmail.com

Apexi Power FC D-Jetro

Thu, 17 May 2012 01:52:19 +0000

Hi Guys,

I have a brand new Power FC D-Jetro with hand controller (including all required harnesses and MAP sensor) to suit Nissan S15 SR2DET. Still in the box it came in. Never been used.

$1050 O.N.O

PM me if interested.

Cheers,

Andrew

Trust Grex Aluminum Gear Knob - 5 Speed. Can Post Oz Wide!

Thu, 17 May 2012 01:05:47 +0000

This style is one of the best JDM gear knobs ever.

Item is used and is in good nick for its age. i have taken pics of it check below

This gear knob feels great when your throwing the gears

Came of a R33, will suit, s13,s14,r32,r33,r34

asking $50

pick up is from Taylorslakes Melb. can post oz wide for an extra $5.

1992 Nissan S13 SR20DE, Manual, Sunroof, P-platers Froth

Thu, 17 May 2012 00:23:02 +0000

Selling my 1992 Nissan S13.

A good write up of the car has been done by Henry Pham from dorifuto:

http://www.dorifutoo.com/2012/04/1685/

Has been owned by me for the last 7 years, bought it when i was on my P's to get to and from uni.

Has slowly been built to what it is today. Being N/A there wasn't much i could do to get more power out of it but I did the most I could without opening up the head, hence suspension/brakes and driveline were all concentrated on, is great fun at skid pan days. Only thing other thing left to do would be to advance the timing a few degrees which will take like 10 mins.

At a guess, the car is making close to 95rwks which is more than enough for to have some fun.

Car has been used by me at skid pan days and numerous drift days however the car is reliable as hell and is regularly serviced either every 7000 kms (when it was my daily) / every 6 months which ever came first / after every 2 events of late.

I drive up 3 hours, skid and drive 3 hours back home never once has the car broken down or been left stranded.

Anyone that knows me can vouch for this.

Car is up to 210,000 kms and still goes like it is new, revs freely, starts first time everytime.

Water pump/belts was changed less than 5,000kms ago, im sure there was more that ive forgotten

Clean car, but body does show its age

Has rego till next year, March 2013 wont come with RWC as i don't have time to organise

Plates do not come with the car

Genuine reason for sale, nothing broken or that the car is going to die. I am traveling later on this year and could do with the extra money. If not the car will sit idle at home.

No joy riders or test drivers. Will only allow test drives for serious buyers.

Alot of the good stuff have already been sold, so it doesnt come with the follow:

15 x 8 - 8 Mesh Wheels with 185/55/15 Federal F1's
Fets front and rear strut braces,
R32GTR 3 slat grill,
Bucket seat
Gktech drift wheel
330cm Dildo gear knob
Bee*R Rev limiter
Apexi SAFC
SZ Roof visor
Aero pods

I will get more pics of the car as it stands later.

ENGINE:

Stock SR20DE
Shortened intake
4-2-1 Jasma extractors
2.5" straight through exhaust
Punched Cat

SUSPENSION/BRAKES/WHEELS/DIFF

SR20DET calipers/slotted rotors/QFMARM1 pads
Tein HA 8/6 Coilovers
Rear R32 GTR Swaybar
Stock wheels/Work Ewings
R200 with a 1.49 shim
Loom has been tucked for super lowness

EXTERIOR

J's headlights with clear covers with 6000K HID KIT
CA front lip
Aero sideskirts
R32GTR boot lip

INTERIOR:
S15 drivers seat
Momo steering wheel
Sunroof

NISSAN SKYLINE R34 GTT / R34 GT / STAGEA COIL PACKS - FULL SET

Wed, 16 May 2012 23:53:37 +0000

Full set of 6x R34 coil packs off my R34 GT-T.

They were pulled off my R34 a few years ago, at the time it had approx 60,000KM on the cluster.

They are in excellent used condition and will suit R34 GT-T, R34 GT and WGC34 / WGNC34 Stagea.

Im after $75 for the set, will not seperate.

Pickup is available from Rouse Hill in Sydney or I will post at buyers expense.

If interested, please give me a call on 0468 895 020.

SSR Gartmaier

Wed, 16 May 2012 23:52:55 +0000

Hi guys,

Up for sale is a set of rare SSR Gartmaier wheels.
18x9 +38 fronts, 18x10 +38 rears.

Condition is like new, no gutter rash at all.
Size is nice and fit flush on a lot of cars.
Location is Brunswick, Melbourne.

Can deliver them Aus-wide very cheap.
$1600.

Feel free to contact me anytime
- pm
- text 0433552745
- email cheap.wheels.direct@gmail.com

Regards
Gerald.

White Evo 7 With All The Goodies

Wed, 16 May 2012 23:52:33 +0000

IF YOU CAN FIND ME A BUYER FOR THE CAR, I WILL GIVE YOU $1,000 TO REWARD YOUR TIME AND EFFORT, THANKS

carsales link for more info

$38,000.

Here is the specification of the car, please have a look.

Engine and Driveline:
- EVO 8 bottom end (short block)
- ARP Headstuds and brand new OEM headgasket
- GTpumps td06-20g turbo
- EVO MR Blow-off Valve
- Brian Crower 272degree intake&exhaust camshafts
- Brian Crower adjustable cam gears
- Gates racing timing belt
- Gates racing balance belt
- Gates racing alternator belt
- Precision 1200cc injectors
- HKS EVC VI Electronic Boost Controller
- Exedy twin plate clutch + braided clutch line
- HKS Silent Hi power cat back
- Invidia dump pipe
- TurboXS front pipe
- Magnaflow 3" metal cat
- Walbro GSS342 500hp 255lt/hr fuel pump
- HKS Racing Suction pod intake
- x3e 52mm alloy radiator
- 1.3bar radiator cap
- NGK Super Power Cables ignition leads
- NGK Iridium BPR7EIX spark plugs
- Pivot Raizin volt stabilizer
- Pivot Super Earth grounding kit
- Beatrush radiator cooling panel
- Blox billet engine mount
- Engine torque dampener
- ETS Version 2 Lower Intercooler Pipe
- Reflashed ECU (dual map e85 / 98ulp)

Handling and Braking:
- BC type ER coilovers with external reservoir
- Whiteline 22mm adjustable rear sway bar
- DBA 4000s slotted rotors front and rear
- Ferrodo DS2500 front brake pads
- x3e rear brake pads
- Goodridge braided brake lines

Interior:
- Alpine CDA-9853 head unit
- Focal 165 CV1 speakers
- APEXi Full auto turbo timer
- Trust shift knob Type N
- Fixed in-car camera mounts
- CAMS Approved 1kg fire extinguisher with fixed racing mount
- Carbon fibre wrapped interior panels, stereo surround, window switches
- Black faced boost gauge
- 52mm Autogauge Oil Pressure gauge
- 52mm Autogauge Oil Temperature gauge
- 52mm Autogauge Water temperature gauge
- Evo 9 Steering wheel

Exterior & Cosmetics:
- EvoXenon's Custom Headlight & Projector
- HKS inspired front lip
- OEM Evo 9 rear bumper with OEM tow hook cover
- Voltex genuine CF rear diffuser
- Chargespeed side skirt extension
- Carbon fiber boot lid lip
- Carbon fiber vortex generator
- Zaklee Corp clear cam pulleys cover
- Repainted valve cover
- XXR 527 17x9.75 +25 in matte bronze
- 255/40/17 Bridgestone Potenza RE001
- D1 Spec racing lug nuts

PS. My best contact methods are SMS and Emails as I do not pick up calls at work.
0433552745
[email=""]geraldi.eka@gmail.com[/email]

Cheers,
Gerald.

GENUINE NISSAN S15 200SX / SILVIA ABS BRAKE UNIT

Wed, 16 May 2012 23:52:13 +0000

Excellent condition, removed from low KM car.

Pickup is available from Rouse Hill in Sydney or I will post at buyers expense.

If interested, please give me a call on 0468 895 020.

R34 GTR NISMO LIGHTWEIGHT FLYWHEEL - RSR41

Wed, 16 May 2012 23:50:18 +0000

Excellent condition, had only been in the car for a few months.

Great direct replacement for the stock Nissan Skyline R34 GTR dual mass flywheel and 60 - 70% lighter.

Part number is RSR41. More info on weight, features, benefits - etc is available on the Nismo website -

http://www.nismo.co....df/clutch07.pdf

Im looking for $295 for it.

Pickup is available from Rouse Hill in Sydney or will post at buyers expense.

If interested, please PM or call me on 0468 895 020.

EARTHQUAKE TREMOR TNT AMPLIFIER / AMP - AS NEW

Wed, 16 May 2012 23:48:52 +0000

Still in as new condition, was only used for a short time.

600 watt, 4 channel and bridgeable.

Im looking for $145 for it.

Pickup is available from Rouse Hill in Sydney or will post at buyers expense.

If interested, please PM or call me on 0468 895 020.

5x100 5x114.3 ALL NEW XXR 530

Wed, 16 May 2012 23:39:39 +0000

XXR 530 - BRAND NEW FOR 2012! XXR 530 wheels feature a deep concave spoke design, with maximum brake clearance.
The modern Euro-styled design looks great on many types of cars, and comes in a wide range of sizes from 15"- 18" with staggered fitments available.

Features

Deep concave wheel design
Wide range of fitments
Genuine XXR logo center cap included

5x100/114.3 in 17x9.75 +25 Chromium Black / Flat Black / Gold.
We can do staggered fitment for Flat black and Chromium black with 17x8.25 +25 fronts.
A set of center caps is included.

Price is $1050 delivered.

Contact us:
- PM
- Email to cheap.wheels.direct@gmail.com
- 24/7 SMS 0433552745

Regards
Gerald.

5x100 5x114.3 ALL NEW XXR 530

Wed, 16 May 2012 23:38:25 +0000

Deep concave wheel design
Wide range of fitments
Genuine XXR logo center cap included

5x100/114.3 in 18x8.75 +20 or +35 in Gold.
A set of center caps is included.

Price is $1150 delivered.

Contact us:
- PM
- Email to cheap.wheels.direct@gmail.com
- 24/7 SMS 0433552745

Regards
Gerald.

4x100 4x114.3 NEW XXR 530

Wed, 16 May 2012 23:27:06 +0000

Deep concave wheel design
Wide range of fitments
Genuine XXR logo center cap included

4x100/114.3 in 17x9.75 +25 Chromium Black / Flat Black / Gold.
We can do staggered fitment for Flat black with 17x8.25 +25 fronts.
A set of center caps is included.

Price is $1050 delivered.

Contact us:
- PM
- Email to cheap.wheels.direct@gmail.com
- 24/7 SMS 0433552745

Regards
Gerald.

S15 Power FC & Hands Controller

Wed, 16 May 2012 22:55:32 +0000

Power FC & Hand Controller to suit S15 & S14a (please check)

BRAND NEW - NEVER USED - BOX NEVER OPENED

Bought from Nengun 2 years ago but never used and car now gone.

looking for $950 ONO.

CALL / TEXT ROB on 0411873469

RB25DET Cylinder Head Drop In Cams VCT Gear

Wed, 16 May 2012 22:17:23 +0000

for sale:

R33 GTSt RB25DET 98% complete cylinder head with the following:

Hks step 1 inake camshaft - not even 700klms on this
unknown (tomei) exhaust camshaft
VCT cam gear for intake
external VCT supply feed line from remote (braided)
standard springs & valves

MISSING 2 CAM CAP COVERS

this head is currently in pieces in boxes, i can arrange to have the head serviced and assembled if needed for a extra charge.

looking for $1000 as is

Location southwest Sydney NSW

Pictures will be up by the weekend.

NEW Tomei Expreme Dump Pipe

Wed, 16 May 2012 21:43:59 +0000

100% Brand new Tomei expreme dump pipe, made for s14 s1/s2 and s15. never used ! never installed either. only opened to take photos. Bag with glue and stickers and gaskets have never been opened either.
Everything is in it's original packaging. Asking $300

PM me to have a chat

CLARION Max386vd

Wed, 16 May 2012 17:17:46 +0000

it's from my Subaru ! change car = change system = need to go
in good condition !
play dvd - you can buy a wire to use as aux -
you can go on Clarion website to check out for the feature
RRP = $900
can see a place sell it for $600 brand new
350 O.N.O
will be in need of cash so quick bargain will get this
Advanced Features with Refined Cosmetics

The MAX386VD 2-DIN multimedia station lets you listen to MP3 and WMA music files burned on CD-R/RW or DVDÂ±R/RW for hours of audio entertainment, with high quality sound by virtue of its 24-bit D/A converter. The 6.5-inch screen delivers a superb DVD playback picture and also provides interactive touch panel control.

DVD-Video/DVDÂ±R/DVDÂ±RW/CD-R/RW Ready
MP3/WMA Compatible with ID3-TAG display
18 FM, 6 AM station presets
iPodÂ® Direct Connection and Control (Optional CCUIPOD1 Cable Required)
6.5-inch QVGA colour LCD monitor
Touch panel control
Phone mute
24-bit D/A converter
6 ch RCA output (front + rear + subwoofer)
4-channel Ã— 40 watts built-in amplifier
Rotary volume control
Built-in IR eye and remote included
Rear audio and visual input
Rear AV output
24-bit D/A Converter: Music Reproduction at Its Best

The 24-bit D/A converter delivers a sonic experience beyond CD quality. The only way to experience the sonic impact of DVD movie soundtracks or music videos is through 24-bit processing. Clarionâ€™s 24-bit D/A converter eliminates the signal defects of older 16-bit decoding by actually â€œoversamplingâ€� the digital signal. This greatly improves the overall sound quality of the D/A converter, creating a more natural sound and superior images.

6.5-inch Touch Screen Control with QVGA Display

The MAX386VD features a large 6.5-inch LCD screen with touch screen controls. Simply touch the appropriate area of the screen for complete control over CD and DVD audio playback, as well as complete touch-screen access to DVD menus. The high-resolution QVGA LCD screen delivers awesome video quality from DVDs or another video source connected through the A/V input.

S14A! You Buy Now. Cheap.

Wed, 16 May 2012 13:47:12 +0000

Just a quick basic write up now.... Will post more details and photos asap.

Nissan Silvia S14 Series 2
SR20DET
5 Speed
Morpheus Purple
FRP Bonnet
3in Turbo back
Front mount
Manual boost bleed valve
Pod filter
Slotted Discs
Some kind of subwoofer (Didn't take notice.)
HID's
No rego or RWC (Have list - not much needed)

8k ono!
Will sell $500 cheaper with stockies or $800 cheaper if you BYO wheels!
Throw me an offer!
No Swaps - Need cash money (Unless you have a car in Japan?)

I bought this car for a street car now my 32 is track only.
But now plans have changed and going to Japan so I need the dollars to buy a car over there!!

Car will be going on ebay very soon.

Rb25 Spitfire's, Z32 Airflow Meter And Heaps More..

Wed, 16 May 2012 13:18:03 +0000

RB25 Spitfires - $300

Z32 airflow meter with plug - $200

R33 series 1 bonnet - $150

R33 series 1 headlights pair - $250

R33 series 1 front guards $100 each

R34 GTT stockies decent tread - $500

R33 Whiteline front sway bar - $150

R33 Cusco 1.5way diff - $800

Location: Bundoora

Contact: 0409 079 070

Apexi AX53B70 Turbo, Braided Lines & Dump Pipe RB

Wed, 16 May 2012 13:16:17 +0000

Up for sale

-Apexi AX53B70 turbo in excellent condition with minimal shaft play (p25 rear housing & t3 flanged)
-Comes with oil & water braided lines
-AM Performance Dump pipe
-silicone elbow
-modded intake pipe

I've made 240kw with this set up, has more go but car had boost leak at the time. So I havn't returned for another dyno run
Awesome set up for the street as it is low mounted & away from prying eyes

suit rb20/rb25 engine

$800 firm

RB26 180SX 99% Done

Wed, 16 May 2012 11:52:17 +0000

99% done Project Car RB26 DET 180SX

Hi Guys, it’s a 99% done project 180SX with the Gozilla RB26DET engine and below are the details:-
89 Nissan 180SX
R32 GTR RB26DET
Tomei Type R poncams
Sard 700cc injectors
bosch 040 fuel pump
trust/greddy oil cooler including remote filter relo kit.
generic fmic
tripple layer copper radiator
retains 6 throttle and std plenum
Trust T78 33D
Trust Manifold
Trust 50mm Gate
adjustable fuel reg
Twin Z32 AFM and Greddy Y pipe.
low temp thermostat
screamer
3inch exhaust through muffler under the car and twin 3inch pipes
Power FC with H/controller
HKS GD PRO Twin Plate
RB25 Gearbox (mint)
custom tailshaft
2 Way LSD
5 Stud
R33 brakes and rotors
New brake Braided lines all round
Brand New Ferrodo Brake Pads x 4
Full Cage 6 Point Bolt In
S14 Rack, a31 lca's, s14 tie rod ends, s14 knuckle with heaps of lock somehow...
speco oil temp oil press and water temp gauges
nardi wheel
"bride" style seat (vios 3)
bride rail
Gab revo stroke 2 coilovers front
BC BR coilovers rear
adjustable castor
R32GTR Rear swaybar
Volk TE37s in 17x9.5 +28 (25mm spacer)
Volk TE37s in 18x10.5 +15
CA front bar with lip
nissan "aero" skirts
vertex rear bar
vented fibie front guards (not yet on)
sunroof
All you need to do is to get a custom radiator and fan, Tune it and see it let loose!
Price: $12800 ono

Rb 20 AFM (cefiro)

Wed, 16 May 2012 11:19:53 +0000

pulled my rb20 out that blew up and was a ceffy 20 and im replacing it with a r32 20 so changing the afm. is in good condition was working fine before motor blew ( ran out of compression the rings went) contact digby 0430 646 937

Individual Throttle Body Setup. GTR & Universal

Wed, 16 May 2012 11:13:26 +0000

I'm selling up and getting out of imports except for my daily, so all the stuff I have accumulated over the years is going to be progressively sold off to get a house deposit together. Today I've got:

Individual Throttle Body setup from a GTR (ITB plates, linkages & plenum) as well as 7 O'ringed flanges to suit. Perfect for a custom start to an ITB setup for an inline six, such as a JZ.

Throttles measure 45mm.

Either use 3 flanges to match up to your engines runners/injector stub. Or use 6 to make a custom plenum as I planned to. The extra flange is for a spare just in case.

If the buyer is going to adapt it to a 1JZ I'll even throw in a spare injector stub to just up for flanges or weld onto.

$600 ono

If it doesn't sell, I might finish the stub myself and set it up using the GTR plenum.

RB20 DET Manual Gear Box

Wed, 16 May 2012 11:12:10 +0000

have for sale my spare RB20 gear box. its taking up to much space in the shed need to clean it out. gear box has done around 160,000 kms feels really good. doesnt crunch or grind when changing gears. will swap for turbo to suite a rb 20.
message digby on 0430 646 937

Nissan 180sx

Wed, 16 May 2012 11:09:32 +0000

pretty much helping sell this car for a customer. so i may have to come back and fill in some details. or any questions PM ME AND I WILL PASS THEM ON.

basic rundown:
Nissan 180sx, early model
SR20DET, Manual.
cut front bar for intercooler and topstage lip, factory side skirts and type-x wing.
engine mods are very low KM disco potato and front mount intercooler, full 3 inch exhaust. HD clutch
mods not fitted: top feed 550cc injectors with rail and fittings to suit, and an x-force low mount manifold.
car is fitted with a 6 point weld in cage build by independent motorsports and morwell, and a drivers OMP fixed back seat with 4 point harness.
has 5 stud hubs and R32 brakes fitted all round, and height adjustable coilovers. tyres are near new

also comes with a shitload of spares. another full set of 15s with new tread (one is odd and 4 stud though) an extra bonnet, and p[air of front guards, a spare diff, and a heap of other stuff.

car is really really straight and the rails seem to be in great condition too. but it can't be registered as it doesn't have compliance...it is located in glengarry (just out of traralgon) in victoria.

owner is chasing 8k, but is open to reasonable offers.

600x300x76 Polished Intercooler

Wed, 16 May 2012 09:48:09 +0000

600x300x76 Polished Intercooler
$150
Pick up or will post at buyers expense

S13 Silvia/180SX Engine Damper

Wed, 16 May 2012 09:45:58 +0000

S13 180SX/Silvia Engine Damper
Complete with custom stainless steel polished strut tower mounting bracket
$100 pick or wil ship at buyers cost

JJR 30mm S13 Front Sway Bar

Wed, 16 May 2012 09:16:15 +0000

JJR 30 MM front sway bar to suit s13
had it in my cefiro for a while but doesnt fit properly with an RB over the top of it so need somethign else
my loss is your gain

brand new they retail for $149

im doing half price $75

pick up only

S13 Sr20det

Wed, 16 May 2012 09:16:02 +0000

Hey people,

Selling this for a mate. so dont bother pm'ing me.

Pics on eBay link:
http://www.ebay.com....em=261025720314

Nissan Silvia 1993 5 speed manual (short shift) SR20DET K's model

HUD (Head up display) Dash works fine dims when head lights turned on, except taco is stuffed, have electronic rev metre on steering colum
3 weeks rego ONLY expires June 4th
have over $2000 of reciepts in the past couple of months + $1089 for s/h engine
Front bar is rubbish but have brand new CA NON TURBO front bar painted ready!
gearbox is fine, clutch is brand new
New fitted s/h engine, runs very smoothly without noises, had a bore scope in the cylinders and there is no marks or scratches.
Garret 28/60RS Turbo 14 PSI actuater (No Shaft play at all)

Turbosmart BOV vented to atmo
3" stainless exhaust with mild 3" dump pipe

Race series Alloy Radiator with twin thermo fans run off an external automatic switch.
Front (original Nismo) and Rear Strut braces

Pedders Coilovers in Front only - Harden Shocks in the rear.
new walbro race series fuel pump
fuel tank cleaned from gunk etc
new battery
new intercooler piping - Front mount sprayed black
heat wrapped intake pipe and vacuum lines near turbo
catch can with NO blow by
all cylinders are at 150PSI tested by mechanic
s/h fitted HICAS power steering pump
New silicone hoses where was needed
pod filter intake
Interior is standard, has drift button and nardi drift steering wheel, GReddy Turbo Timer and GReddy Boost Guage

Have a bride seat availabe for right price NOTE SEAT IS NOT INCLUDED IN THIS AUCTION UNLESS CAR SELLS FOR $4200!

de-winged but holes havent been welded (didn have time but still have wing)

Asking $4200 ONO i dont want any low ballers or stupid offers

I NEED THIS GONE CAN NOT RELIST I LEAVE IN TWO WEEKS!

im selling these very cheap because im moving north for work.
Have lost ALOT of money on this all my friends and mechanic espescialy can vouch for this!

Tom 0414443626 msg throuhout the day or call after 4pm for any questions

S15 200sx Front Seat Pair With Rails

Wed, 16 May 2012 09:00:27 +0000

Hi
i am selling my s15 200sx front seats
no rips or tears
fabric type with rails. i upgraded, good upgrade for s13/4
$400 firm in sydney 2145
Thanks. joshua 0412788262

S13 Drift Car Stripped. Parts Galore

Wed, 16 May 2012 07:47:13 +0000

hey people i will be stripping a drift car over the weekend so everything is up for grabs

GT2530, good condition no leaks or smoke ect, boosts hard and always run at 10psi - $700

G4 front and rear coilovers, 8kg front 6kg rear, base height, spring height, camber and damper adjustabel. these are basically brand new barely used $850

Greddy copy inlet manifold for sr20det, good condition $250

stainless steel sr20det turbo manifold $150

ACL race series forged pistons with ring set, brand new still in box 86mm $550

GTR intercooler with pipe work to fit sr20 with greddy or late model inlet manifold, core is a bit bumped and bruised but no leaks - $200

stainless steel split dump pipe and 3 inch straight through exhaust system. pipe work looks abit thrown together but it doesnt leak and sound tough, $350

s13 sr20det manual conversion kit. comes with EVERYTHING. gearbox, flywheel, used aftermarket clutch, tailshaft, brake and clutch pedal, master, slave and lines - $900

oil catch can setup, sts behind radiiator and above the fan, one of the ones that lies down, comes with braided shealthed lines and brackets -$100

sr20det cylinder head, was recondiitioned and mildly ported, i bought it second hand so could probly do with a face. $350

copper core radiator, thicker than standard, ive never had a overheat issue with this radiator as apposed to my alloy 3 core - $150

standard s14 radiator, no leaks when removed, could do with a wash out - $50

s13 front strut brace - $80

onevia shell, has been hit on rear left quarter by tyre stacks at lala, two tone white/ silver with champaign 180 front, will need you to bring standard suspension to get rolling but has 5 stud rear conversion
straight chassis, good track hack shell - $500 . could get this from stripping the shell to nothin

Recaro copy bucket seats on custom rails retrimmed in leather AND factory leather rear seats all in excellent condition. make your s13 pimp! $750

up for sale shortly will be the turbo setup off my s13 as im looking to upgrade
gt2871r (ballbearing) with .86 exhaust housing, need to confirm trim
greddy style inlet manifold with standard throttle body
intercooler pipework to suit including provision for BOV behind front bar to be all sneaky n shit (core not included)
s15 injectors highflowed out to 540 or 550cc (i forget)
factory exhaust manifold if required
braided turbo lines

$1900

turbo setup makes 220 rwkw on 14psi boost (low boost if due to running a stock internal engine so i didnt want to put too much boost in it) this was on a microtech and tuned by the fellas at jaustech. plenty left in this turbo should make 260 at 18psi pretty easily. i can also throw in a brand new .62 exhaust housing for $150 incase you want to change it over

all parts are located Northern sububrs of adelaide

easiest contact is via text on 0448 032 395

JDM Black Aero S15 Immaculate Car Fresh Respray Must See!

Wed, 16 May 2012 07:35:07 +0000

Up for sale is my pride and joy a absolutely immaculate s15 Silvia..
Sadly it has to go I really need to clear up some debt and get something more practable !
Car is only ever driven on weekends and always garaged and serviced with the best of products!
I am a ridiculously picky owner being a panel beater by trade and complete neat freak
First to see will definetly buy so get in quick ! Yea it's not the cheapest but it's the best you'll find ,buyer will not be disappointed ! Don't like the price buy another one
The entire car just received a flawless professional respray in the factory colour at Allan Doyle crash repairs it has 10,000 worth of paint work on 30/04/12 this includes all inner wheel arches in a black stoneguard !
sadly my loss is your gain but it's time to move on .

Car is not too loud and dosent attract any unwanted attention never been pulled over or defected , but if it was to be defected it comes with the standard suspension anyway

2000, JDM S15 with factory fitted areo body kit +option b package

- 6 speed manual
- 104,XXX kms
- Factory fitted areo kit
- factory hid headlights
- nismo clear indicators
- genuine jdm model
- Tomei stainless steel dump pipe
- HPI split stainless steel front pipe
- 3inch stainless steel Jasma catback exhaust
- Greddy LS spec intercoller kit
- Split Fire coilpacks
- Exeedy Heavy duty clutch
- Nismo front strut brace, Rear Factory brace
- Factory airbox with apexi panel
- Turbosmart boost Tee (set to 12psi)
- Greddy style oil pan
- HKS oil cap
- Walbro fuel pump
- Racing logic coilovers( Front with adjustable camber tops) hight and damper adjustable
-tie rod lock spacer
- Front DBA slotted rotors with EBC greenstuff pads
- Rear converted to R34 GTT brakes with drum style hand brake and twin piston calipers
- Cyclops alarm
- 20% tint fronts / privacy tint glass rears
- Factory fitted weather shields
- Factory electric fold in side mirrors
- Yashio Factory shift knob+boot
- yashio factory drift button
- Alpine head unit with Ipod cable
- Pioneer splits the front and tweeters
- rear 3 way pioneers 6 inch
- alpine amp
- 12 inch pioneer sub in a moulded corner box out of a show car fits perfect carpeted to Match the factory trim
- Factory Option blue suede seats with Silvia emblem and Blue suede door inserts
- genuine Silvia floor mats
- factory boost pillar guage
- 17x9+17 bronze p1s all round
- new top of the range TOYO 245/45 tyres fitted
- all inner wheel arches black stone guarded
im sure ive missed some things...
Comes with standard suspension
3 months rego
Price is negotiable at $24,500 Genuine buyers only no tyre kickers for the right person I'm sure we can work out a good deal as I no ya can't always get what ya want or make all ya money back so I'm open to reasonable offers Some trades considered such as s13 Silvia/onevia/sil80s immaculate street versions or well setup track version with cash my way Contact via SMS preferably on 0431280172
cheers
Tyson

Classifieds RSS Feed

S13 Ca Seats + Swap Cusco Brace

Pignose 180sx Conversion.

2x Rays TE37 (17x10JJ+18) Matte Black

NSW SYD: '89 Ti Nissan R31 Skyline, 270rwkW RB25DET

18" SSR "Premium Agle" Wheels

FS - R32 Bonnet, R32 Guards, R32 Doors,

Project NA 4.0 P Plater Legal SR20DE Silvia

18 Inch Tyres

Few Sets Of 17inch Wheels And Tyres For Sale

F.S Nissan Navara 2010 ST Dual Cab 24 Inch Wheels

Ford Trader Dual Cab Tilt Tray Tow Truck

Work Emotion KAI Rims And Tyres

Bucket Seat New Bride Copy

HKS SILENT HIGH POWER CATBACK EXHAUST MUFFLER SUBARU IMPREZA GRB

HKS FULL DUAL MUFFLER CATBACK EXHAUST NISSAN Z33 350Z VQ35DET

HKS SILENT HIGH POWER CATBACK EXHAUST MITSIBISHI EVO 9 4G63 CT9A

HKS KANSAI SERVICE TOWER BAR NISSAN SKYLINE R32/33 GTR RB26 DETT

DEFI ADVANCE BF Boost Gauge WHITE/RED/ BLUE+ADV Control Unit Set

Ducati 400SS Learner Legal

HKS SILENT HIGH POWER CATBACK EXHAUST-NISSAN BNR34 GTR RB26DETT

HKS STAINLESS CENTRE PIPE NISSAN 350Z Z33 FAIRLADY Z

Tomei Oversize Valve Nissan Skyline Rb26 R32 33 34 GTR

Forced Performance Turbo Red BALL BEARING -Mit Evo 4-9-84mm Surg

Forced Performance Turbo GREEN BALL BEARING -Mit Evo 4-9-84mm Su

Forced Performance Turbo Ball Bearing EVO Black-Mitsibishi Evo X

VOLK RACING GT-C Face 2 Rims 17" 2 Peace Rims MAKE OFFER

Nissan S15 Spec B Eyelids MAKE OFFER

Black R34 Gtt *open For Trade*, Tdo6, Twin Waste Gate, External,

Defi Electonic Boost Gauge + Control Unit

Apexi Power FC D-Jetro

Trust Grex Aluminum Gear Knob - 5 Speed. Can Post Oz Wide!

1992 Nissan S13 SR20DE, Manual, Sunroof, P-platers Froth

NISSAN SKYLINE R34 GTT / R34 GT / STAGEA COIL PACKS - FULL SET

SSR Gartmaier

White Evo 7 With All The Goodies

GENUINE NISSAN S15 200SX / SILVIA ABS BRAKE UNIT

R34 GTR NISMO LIGHTWEIGHT FLYWHEEL - RSR41

EARTHQUAKE TREMOR TNT AMPLIFIER / AMP - AS NEW

5x100 5x114.3 ALL NEW XXR 530

5x100 5x114.3 ALL NEW XXR 530

4x100 4x114.3 NEW XXR 530

S15 Power FC & Hands Controller

RB25DET Cylinder Head Drop In Cams VCT Gear

*NEW* Tomei Expreme Dump Pipe

CLARION Max386vd

S14A! You Buy Now. Cheap.

Rb25 Spitfire's, Z32 Airflow Meter And Heaps More..

Apexi AX53B70 Turbo, Braided Lines & Dump Pipe RB

RB26 180SX 99% Done

Rb 20 AFM (cefiro)

Individual Throttle Body Setup. GTR & Universal

RB20 DET Manual Gear Box

Nissan 180sx

600x300x76 Polished Intercooler

S13 Silvia/180SX Engine Damper

JJR 30mm S13 Front Sway Bar

S13 Sr20det

S15 200sx Front Seat Pair With Rails

S13 Drift Car Stripped. Parts Galore

JDM Black Aero S15 Immaculate Car Fresh Respray Must See!

Black R34 Gtt open For Trade, Tdo6, Twin Waste Gate, External,

NEW Tomei Expreme Dump Pipe