Jump to content
Sign in to follow this  
Rex_Kelway

Rex Kelway sucks.

Recommended Posts

Alright Lads and Lasses?

 

Rex would like to thank STR8E180 for creating a Fabrication specific section, it's a great addition in a world full of 'What's the best cheapest coilover' and 'How do u remove mah turbo 4 cheep' topics.

 

The introduction of Rex. He's been working in the import industry for many years and for a few of SA's well known importers. About 10 years ago Rex started learning fabrication as a serious part-time hobby and after leaving His last job 2 years ago, He decided to try and make a go of the self-employed route. He's sure this will be controvertial but while His father is a sheetmetal worker by trade, Rex Himself is completely self taught. Engineering, Design and Fabrication are his reason for existence, sounds lame doesnt it...

 

Most of His fabrication projects are limited ultimately by customers budgets but while this means the complexity often isn't high, Rex's obsessive compulsiveness means no matter how simple, it shouldn't be anything lass than perfect. Even if the piece will never be seen.

 

So He'll throw a few in this thread, and hopefully keep it updated if He can be arsed.

 

BUT! While it's no secret Rex is technically a business (no matter how small), In the interest of fairness always check your forum sponsors! Without them NS.com wouldn't exist.

 

Anyhoo enough crapping on.

 

Rex Kelway sucks...

 

SR Stainless intake hardpipe

DSC00029_wm.jpg

 

Exhaust Rex built for His old AW11 MR2 S/C

CompleteUnderside_wm.jpg

 

Few manifolds mid-build

DSC00034_wm.jpgDSC00338_wm.jpg

 

Custom front pipe and screamer that went into a 1G Celica

IMAG0098_wm.jpg

 

Manifolds, heatshields and dump pipes for RB26/RB25

IMG_0017_wm.jpgIMG_0010_wm.jpg

 

Pretty Basic rollcage in Rex's Rallysprint KE70

IMG_4642_wm.jpg

 

Turbo setup for Rex's 180, eventually...

IMAG0351_wm.jpg

 

RB25 Manifold

IMAG0275_wm.jpgIMAG0272_wm.jpg

 

I/C pipework and cold air feed

IMAG0020_wm.jpgIMAG0017_wm.jpg

 

Couple of manifolds

IMG_5633_wm.jpgIMG_5134_wm.jpgIMG_4884_wm.jpgIMG_1208_wm.jpgIMAG0267_wm.jpg

Share this post


Link to post
Share on other sites

why does rex write in third person?

 

or is this guy narrating your life for you?

 

ThisIsYourLife.jpg

Share this post


Link to post
Share on other sites

He's sure this will be controvertial but while His father is a sheetmetal worker by trade,

wow my old man is a sheety by trade as well

tried getting me into it as well but i was more attracted to the boiler maker trade

 

good work mate

Share this post


Link to post
Share on other sites

I have a feeling STR8E, as this thread goes on you'll find we have a lot more in common :)

Share this post


Link to post
Share on other sites

WTF? Rex's asian? Lol :whistle:

LoL kemp

Is Asian? :P

Share this post


Link to post
Share on other sites

I have a feeling STR8E, as this thread goes on you'll find we have a lot more in common :)

Are you hitting on Asians now Rex?

Share this post


Link to post
Share on other sites

Sorry JDM:180, Rex's doesnt discuss that stuff in an open forum. He classes that as outright advertising which is not allowed :thumbsup:

Share this post


Link to post
Share on other sites

hey Rex, do you do much custom suspension? extending LCA's and that sort of stuff? i'd be interested in some pics of that if you had them =]

Share this post


Link to post
Share on other sites

nice stuff t-rex. cant wait for the next batch of pics. can you make them a bigger size next time?

Share this post


Link to post
Share on other sites

Another installment. Rex thought instead of just posting a pic of each jorb perhaps He would elaborate with a brief description and a few more pics of each.

 

A simple one. Mounting of a base mount seat as low as possibe (without starting from scratch) on some Sparco two piece rails rails. Note the shape of the floor in an S13 means that if you mount the seat the 'easy method' it will be quite high. So with a little work you can go about 25mm lower but the position of the inner rail will bend the mounts so they need gussetting but in such a way that they can slide unimpeded.

 

IMG_5008_wm.jpgIMG_5006_wm.jpgIMG_5005_wm.jpgIMG_5002_wm.jpg

 

 

Some bits and pieces on some car. Rex built a non-divided Expreme type manifold w/ external wastegate and screamer. The Tomei dump-pipe needed to be adjusted and reinforced as the tail end of the MFR front pipe fouled on the body.

 

P1000520_wm.jpgP1000531_wm.jpgP1000529_wm.jpgP1000530_wm.jpg

 

Intake pipework and intercooler 'hot-pipe' along with AFM bracket and a basic filter heat sheild.

 

P1000525_wm.jpgP1000541_wm.jpgP1000540_wm.jpg

 

KE25 Corolla Half RollCage built to customers design. It uses an X-brace across the door opening but without the front legs. The door bars had to be treated as if they were any other reinforced rollcage mounting. They feed into the kick-panel sheet section which on the KE25 is a major steel section tied directly into the suspension mounts. Personally Rex would've liked to have seen the backstays and the rear quarter brace feed directly into two proper 'nodes' at the top outermost corners and at the opposing edge of the upper door member.

 

IMG_0371_wm.jpgIMG_0370_wm.jpgIMG_0375_wm.jpgIMG_0376_wm.jpgIMG_0368_wm.jpgIMG_0367_wm.jpgIMG_0366_wm.jpgIMG_0361_wm-1.jpgIMG_0362_wm.jpg

Share this post


Link to post
Share on other sites

Some really nice work!

 

Custom seats mounts have given me ideas how ill takle r32 gtr seats in my gazelle.

 

 

Share this post


Link to post
Share on other sites

damn dude! your work is pretty shmick! love seeing your updates in any of your threads

Share this post


Link to post
Share on other sites

Even though I hate this third person speaking!!

 

Rex's work is awesome!

Share this post


Link to post
Share on other sites

Rex my man... Hats off to you sir.

Share this post


Link to post
Share on other sites

why does rex write in third person?

 

 

 

Agreed, whats up with that?. However great work.

Share this post


Link to post
Share on other sites

One for the 'dwyfterz' or whatever the hell you lot want to be called. This is Rex's method for mounting ye ol'e hydraulic handbrake. Its a sheetmetal box section that is welded onto the tunnel providing a decent mounting pad. Each of these are built specifically for the owners preferred position and angle. One even wanted to relocate the original handbrake to the passenger side. The black car had the lever modified so it would work reversed into an upright position.

 

DSC00150_wm.jpgDSC00152_wm.jpgDSC00156_wm.jpgDSC00190_wm.jpgDSC00192_wm.jpgP1000403_wm.jpgP1000395_wm.jpg

 

 

A few more pics of the stainless lobster-back style exhaust Rex built for His old AW11. The driveway of some trucking joint destroyed the stock exhaust so Rex took a massive Tanabe muffler designed for a late model MR2 and fabricated the pipes from the factory manifold back. This was actually Rex's first lobster-back project. The thing sounded fantastic far better than He'd hoped. Funny thing is that although the lobster-back style of pipework takes far, far longer it is actually nice to work with because the segments can be adjusted for different curve raduii but most importantly bends can be formed in three dimensions.

 

IMG_3380_wm.jpgIMG_3379_wm.jpgIMG_3378_wm.jpgIMG_3376_wm.jpgIMG_3374_wm.jpgIMG_3369_wm.jpg

 

 

Another basic rollcage, this one was installed into a well known SA drifter's SR powered KE70. Its only a CAMS spec basic 6-point full cage, again built down to a budget. Worth noting is that with the mounting feet Rex tries to take in more than one piece of sheetmetal or more than one plane in the chassis. All Rex's full cages are built very tight and tied to the chassis with swaged gussets to both the A and upper B pillars so even a basic roll cage adds to the chassis. Surely someone must want a nice comprehensive rollcage built?

 

IMG_5226_wm.jpgIMG_5225_wm.jpgIMG_5227_wm.jpgIMG_5228_wm.jpgIMG_5232_wm.jpgIMG_5237_wm.jpg

 

 

This was His first twin-scroll/divided housing manifold build, it was bulilt for a T67 to go onto a 1J powered Cefiro. He's not sure what ever happend to the car though.

 

IMG_5264_wm.jpgIMG_5263_wm.jpgIMG_5268_wm.jpgIMG_5255_wm.jpg

 

 

A few basic slut bars including a batch of 10 Supra braces built for the Toymods lads. They're built from structural grade aluminium with stainless end plates. All up they weigh around 1kg. Rex tries to keep the bar as straight as possible as they are a compression loaded item where a bend introduces a failure point. Sometimes though with the height of the motor and lack of clearance under-bonnet a shaped bar is unaviodable.

 

IMG_0384_wm.jpgP1010102_wm.jpgP1010093_wm.jpg

Share this post


Link to post
Share on other sites

hey rex, ask rex why he has chosen to make that style of slut brace, compared to the solid style that Ultra racing make? would have thought the less pivot points the better. and if you make this sort of brace, do you make the lower arm braces like castor rod braces?

Share this post


Link to post
Share on other sites

fyjosh,

 

Rex builds the bolted braces because after this many years cars eventually get a little 'out' be it through damage or whatever and a little adjustment can be built into the bolt holes to allow for all sorts of dimentional variations.

 

Strut braces are designed to tie the towers together so that the cornering force pusing the outer tower into the engine bay is resisted by the opposing tower. The surface area clamped by the bolted joints takes an extroadinary abount of force to rotate as it is. Given the upper plate is secured to the top it transmits the force directly down the bar in a rather than attempting to fold it at the bolted points. Lozenging of the towers in the vertical plane is another matter all together, while the bolted joints may pivot under lozenging of the towers this type of load will also twist a solid brace quite easily. Its a combination of strut and guard braces that will resist the lozenging of the towers.

 

Jesus, why cant Rex just give a simple answer...

 

 

Anyhoo another batch:

 

Quite often Rex gets jobs to replace/rebuild/rework some intercooler pipework. On the S13 below the intercooler was just sitting loose in the front so Rex fabricated some mounts to keep it there and replaced the original medley of ill fitted steel pipes. He also built the basic legal oil/air separator tucked into the corner

P1000803_wm.jpgP1000797_wm.jpgP1000802_wm.jpg

 

 

The difference just decent pipework can make:

 

From this:

P1000382.jpgP1000384.jpg

 

To this:

P1000405_wm.jpgP1000412_wm.jpgP1000408_wm.jpg

 

As a side note, Rex actually built a manifold for this thing to try an experiment with an old Ex-Subaru WRX TD05. It actually makes just over 200rwkw and the tuner said it probably has 240kw of potential in it. Not bad for an old turbo that can be had for less than $200 s/h...

 

 

Pipework for an RB20 VL conversion. The major difficulty was working around the fan clearance as can be seen by the double kink at the shroud.

P1000562_wm.jpgP1000563_wm.jpgP1000564_wm.jpg

 

 

Headers for a mates 4AGZE into TA22 Celica conversion. Not performance headers at all, just built to do the job as the TRD ones didn't fit.

DSC00088_wm.jpgDSC00091_wm.jpg

 

 

A fair bit of work from another Celica:

P1010007_wm.jpg

Reworking the actuator on the Ford throttle so it can be 'pulled' from the opposite directon. The plenum is not Rex's, but he did have to repace the front end, throttle flange and cable bracket.

P1010018_wm.jpg

Oil Catch can built from salvaged speedflow gear. Also mounting of the coilpacks and bracketing of the leads.

P1010008_wm.jpg

Heatsheild protecting hydraulics. lobsterback dump pipe and Intake pipe from 200mm K&N down to intake diameter. At first Rex thought it looked silly but eventually He grew to love it. He wants to do one for himself...

P1010011_wm.jpg

IMAG0035_wm.jpg

Intercooler pipework, tucked away where no one will ever see it...

IMAG0036_wm.jpgIMAG0032_wm.jpg

Share this post


Link to post
Share on other sites

Hi Rex, let Rex know I'm loving his work.

 

+1

More pics, btw tell rex to get bigger images? Im interested in seeing the beads

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

×