Jump to content
Sign in to follow this  
caratgolds15

WTB - LOCAL ONLY

Recommended Posts

Anyone have an exhaust manifold?

 

 

My GKTech one has a crack around no.4. Bodgy solution ideas welcome ;)

 

You could get it welded and put extra bracing on it. I think the GKtech manifolds are only a bit over $200??

 

 

Yeah I may get it welded (main issue imo was insufficient welding rod, resulting in weak welds, has now failed at 3, 4 and collector). Its just easier/faster to swap with another, being only transport :) . I contacted Greg, he's working on a version 2 manifold which is a couple months off, and no old stock.

Share this post


Link to post
Share on other sites

looking for a set of gtr rims,anyone got a set lying around?

Share this post


Link to post
Share on other sites

looking for a set of gtr rims,anyone got a set lying around?

 

I think angelo @ trojan motorsport has a set or two not sure how much he wants for them

Edited by LA369

Share this post


Link to post
Share on other sites

WTB r32 4door drivers door card/trim.

and passenger side tail light

Thanks

Share this post


Link to post
Share on other sites

WTB: I'm looking for a SR20DET CAS (Crank Angle Sensor). It must be in good, working condition. Would like to buy one asap. Let me know what you've got by sending me a pm, or contacting me on 0411 086 883.

Share this post


Link to post
Share on other sites

Hi, I'm after a S13 SR20DET exhaust manifold

Share this post


Link to post
Share on other sites

Hi, I'm after a S13 SR20DET exhaust manifold

 

I got one. Gimme a PM and we'll sort something out.

Share this post


Link to post
Share on other sites

Hi, anyone got a S15 stainless steel manifold and also a dump pipe?

cheers

Share this post


Link to post
Share on other sites

Hi guys, I just picked up a cheap 180sx so I'm now chasing a few bits and pieces. I'm looking for:

 

- SR20DET motor - bare or complete!

- manual conversion bits (gearbox, tailshaft, clutch, flywheel, clutch slave)

- a rear hatch (incl. rear wiper arm),

- a good s13 dash,

- s13 indicator swich/stalk

- s13 side indicators (the rectangle ones)

 

Send me a PM if you have any of these bits to offload.

 

Nigel.

Share this post


Link to post
Share on other sites

Hi

 

Urgently seeking an S15 accelerator cable.

 

anyone local have a good condition one they would sell?

Share this post


Link to post
Share on other sites

All good, got one sent down from sydney.

 

Thanks though.

Share this post


Link to post
Share on other sites

^ I've got some S13 vertex copy skirts you can have for $50.

Share this post


Link to post
Share on other sites

would anyone have a s15 right hand side front fender/guard in pewter?

 

pm me if available :)

 

cheers

Share this post


Link to post
Share on other sites

Hey im looking for a caliper upgrade for my S13. Looking for either S14-S15, Z32 or Skyline calipers. Looking at spending approx. $150-$200.

Share this post


Link to post
Share on other sites

Hey guys, still chasing the following:

 

- 180sx rear hatch (incl. rear wiper arm),

- s13 side indicators (the rectangle ones on the guard)

- passenger side engine mount to suit sr20

 

Send me a PM if you have any of these bits to offload :thumb:

 

Nigel

Share this post


Link to post
Share on other sites

well dude,anyone got a good set of coilpacks for a sr20 in a s14?need asap

Share this post


Link to post
Share on other sites

i have just converted my 180sx gearbox to the rb25 gearbox but i found that the shifter now sits too far forward and i need to move it back. Does anyone have a custom shifter or has done this conversion before and found the same issue?

Share this post


Link to post
Share on other sites

not sure yet as its not in the car as the custom tailshaft was too long but it looks like it will hit the plastic and the metal. The kit is from Nizzpro in QLD

Share this post


Link to post
Share on other sites

One of my mate just did a rb25 conversion in his s13 and his shifter inly just hit the metal and we banged in with a hammer and it goes in everygear now...

Share this post


Link to post
Share on other sites

Yeah ok but i think i will make a shifter so that it sits further back in the boot so its closer to stock position.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

×