Jump to content
Sign in to follow this  
A31Cefiro

SA Buy/Swap/Sell Thread

Recommended Posts

1992 Nissan 180SX Race/Drift ONLY Car

 

This car has everything you'll need to get out onto the track, all it requires is some time putting it back together. I imported this car myself for Race purposes only, so it cannot be complied. But their is always more than one way to skin a cat if you get my drift :-)

 

Engine:

S13 Blacktop SR20DET

- Fully Rebuilt

- King Race Bearings

- Nissan piston rings

- ACL Head and Rod Studs/Nuts

- Cometic ML Steel Head Gasket (standard thickness)

- Head fully checked, found to be in excellent condition

- SR20DE Cams (slightly better duration and lift than the DET ones)

- Rocker stoppers

- SARD 550cc Injectors

- Re-Mapped Standard ECU (TBO Racing ECU)

- HKS Blow off valve

-SARD Fuel pressure reg (with gauge)

- Trust GREX oil cooler and filter relocator

- ARC Aluminium radiator (dual core)

- Turbo is a KKK 2664GGA from a blitz turbo kit, journal bearing, external wastgate plumbed from standard manifold (50mm). The turbo should be good for 200 - 220 kW ATW on 18 to 20 PSI of boost.

 

Engine was designed to make a very responsive 200kW ATW and be reliable

 

Engine was only rebuilt as a matter of course so I knew what I had to work with, the engine ran fine and had no problems before the rebuild.

 

Driveline:

- Lightened flywheel and Extreme Drift Clutch

- Standard S13 5 Speed gearbox, in good condition

- 2-Way Mechanical LSD (unsure of type but works very well, ran it in my Skyline for quite sometime)

Suspension:

- ENDLESS Zeal Coilovers allround, base height adjustable and dampener adjustable. High end coilovers, excellent feel. 12KG front springs, 10KG rear.

- Upgraded front and rear sway bars (were on the car when imported) probably CUSCO ones given their colour.

- Solid rear subframe locking collars

- Solid steering bush

- Seam welded front end

Brakes:

- R33 Discs and Calipers with good pads, slotted rear rotors. (5 Stud also)

Interior:

- Full CUSCO/Safety 21 Roll Cage

- Array of gauges - Water temp, Oil temp, oil pressure, boost, exhaust gas temp. All electronic type

- Fully stripped interior, all sound deadenig gone, all A/C and hearter fans/ducts etc gone, just basically a shell of the dash left. Painted in underbody black.

- Monza Racing seat, reclinable type

- 4- Point harness

-Deep dish steering wheel

- Fire extiguisher

- Encolsed fuel system with surge tank, Bosch 042 Pump and high flow EFI filter utilising the standard nissan pump to feed the surge tank

- HKS boost controller (not mounted)

Exterior:

- Carbon fibre bonnet, very very very light weight (quality one too)

- Type X rear tailights

- Rear wiper and eye level light have been deleted (rust starting to form around where the brake light was deleted)

- Fibreglass front bar, needs to be painted

 

Does not come with the R32 GTR wheels pictured.

Comes with R32 GTST stockies and a 3 SPARCO mesh type wheels, yes 3, lent them to a mate and only got 3 back. All wheels are 16 inch.

Comes with lots of extras probably not listed.

 

$6000 or near offer. NO SWAPS!!

Contact me: Daytime 83473599 or 0437247735

 

Photos:

 

http://www.gumtree.com.au/m-my-ad.html?adId=1021371697

 

http://classifieds.n...dvert&t=2225733

Edited by Blimp Footsoulja

Share this post


Link to post
Share on other sites

1992 Nissan 180SX Race/Drift ONLY Car

 

This car has everything you'll need to get out onto the track, all it requires is some time putting it back together. I imported this car myself for Race purposes only, so it cannot be complied. But their is always more than one way to skin a cat if you get my drift :-)

 

Engine:

S13 Blacktop SR20DET

- Fully Rebuilt

- King Race Bearings

- Nissan piston rings

- ACL Head and Rod Studs/Nuts

- Cometic ML Steel Head Gasket (standard thickness)

- Head fully checked, found to be in excellent condition

- SR20DE Cams (slightly better duration and lift than the DET ones)

- Rocker stoppers

- SARD 550cc Injectors

- Re-Mapped Standard ECU (TBO Racing ECU)

- HKS Blow off valve

-SARD Fuel pressure reg (with gauge)

- Trust GREX oil cooler and filter relocator

- ARC Aluminium radiator (dual core)

- Turbo is a KKK 2664GGA from a blitz turbo kit, journal bearing, external wastgate plumbed from standard manifold (50mm). The turbo should be good for 200 - 220 kW ATW on 18 to 20 PSI of boost.

 

Engine was designed to make a very responsive 200kW ATW and be reliable

 

Engine was only rebuilt as a matter of course so I knew what I had to work with, the engine ran fine and had no problems before the rebuild.

 

Driveline:

- Lightened flywheel and Extreme Drift Clutch

- Standard S13 5 Speed gearbox, in good condition

- 2-Way Mechanical LSD (unsure of type but works very well, ran it in my Skyline for quite sometime)

Suspension:

- ENDLESS Zeal Coilovers allround, base height adjustable and dampener adjustable. High end coilovers, excellent feel. 12KG front springs, 10KG rear.

- Upgraded front and rear sway bars (were on the car when imported) probably CUSCO ones given their colour.

- Solid rear subframe locking collars

- Solid steering bush

- Seam welded front end

Brakes:

- R33 Discs and Calipers with good pads, slotted rear rotors. (5 Stud also)

Interior:

- Full CUSCO/Safety 21 Roll Cage

- Array of gauges - Water temp, Oil temp, oil pressure, boost, exhaust gas temp. All electronic type

- Fully stripped interior, all sound deadenig gone, all A/C and hearter fans/ducts etc gone, just basically a shell of the dash left. Painted in underbody black.

- Monza Racing seat, reclinable type

- 4- Point harness

-Deep dish steering wheel

- Fire extiguisher

- Encolsed fuel system with surge tank, Bosch 042 Pump and high flow EFI filter utilising the standard nissan pump to feed the surge tank

- HKS boost controller (not mounted)

Exterior:

- Carbon fibre bonnet, very very very light weight (quality one too)

- Type X rear tailights

- Rear wiper and eye level light have been deleted (rust starting to form around where the brake light was deleted)

- Fibreglass front bar, needs to be painted

 

Does not come with the R32 GTR wheels pictured.

Comes with R32 GTST stockies and a 3 SPARCO mesh type wheels, yes 3, lent them to a mate and only got 3 back. All wheels are 16 inch.

Comes with lots of extras probably not listed.

 

$6000 or near offer. NO SWAPS!!

Contact me: Daytime 83473599 or 0437247735

 

Photos:

 

http://www.gumtree.com.au/m-my-ad.html?adId=1021371697

 

http://classifieds.n...dvert&t=2225733

 

Please don't sell it man.

Share this post


Link to post
Share on other sites

Pair of rear Tein Super Street coilovers to suit 180/s13/r32, good cond and not knocking - $250

 

Hks catback exhaust to suit 180sx - sold

 

0433943034

Edited by TURBZ6

Share this post


Link to post
Share on other sites

Wtb forged or not ca18det plus gearbox everything needed started motor ect ect Have cash for right motor

Share this post


Link to post
Share on other sites

¥S15 parts for sale¥

 

~Near new Apexi Power Fc.

The latest EL type controller.

Can put OEM ecu covers on it for you incase of regency.

Only 5,000 k's since imported through streeter.

$950 ono

 

958DB80D-E94D-42BD-8735-BD413125A7A5-2005-000001E7EC7574B8.jpg

2CEB5EAD-CA62-4588-89B0-4A41BA75B9F3-2005-000001E81483D9EA.jpg

7679D634-4CBB-492E-9C0E-9A83C3B4714A-2005-000001E38D69F66D.jpg

 

~Tomei 2-way diff

Near new complete in housing/3,000 k old redline oil and 3.69 manual S15 ratios.

$850 ono with stock diff change over

 

~S14/15 half cage.

Made to CAMS spec by bonds roll bars in sydney and is Vic Drift passenger OK

Unpainted or can paint in your choice of colour (was going to go gtr midnight purple along with the wheel centres if anyone is interested in it)

Brand new black padding throughout, had approval by 4 different police officers during street duty lol

$650 ono

 

93AAA213-0673-4F65-A9F2-565A4147B60E-2005-000001E357A3F240.jpg

6F085D9E-F825-4CCA-A609-4031DBDAB053-2005-000001E372EF22BA.jpg

A104DCCA-C743-4F64-866A-FEB83F22950C-2005-000001E2B23F65E2.jpg

 

Garrett GT3071 T2 .86

Mint turbo, perfect condition and couple with a HKS actuator

$900 ono

 

C27F3066-F906-45E4-93B0-B7B3937044C1-125-00000005A637C054_zps4c5e977b.jpg

 

Yashio Factory direct ignition system with S15 coil packs included

$300 ono

 

Tomei sump pan (genuine)

$400 ono

 

HKS 3.5 inch cat back with 3inch high flow cat and GKtech 3inch front and dump turbo back (again cop approval/has a mid muffler and rear cannon)

$800 ono

 

Radiator air diversion plate (Blitz)

$80

 

Brand new GK tech (unused) V2 billet castor rods/extra lock spacers and handbrake extenders package

$200 the lot ono

 

Cusco BMC

$80 ono

 

T28bb again mint internals dirty however (refer top pic)

$400 ono

 

Brand new/15 kilometres total driving Work Stitch

17x8 +5 / 17x9 +11

(perfect full lock inner clearance and flush guard fitment on all S-chassis.)

Can strip tyres but they're brand new.

3 piece sick as shit f**k ya cheap wheels pricing

 

$1600 ono

12a60a47fb6043592e0488189ae94ec7_zps969697d4.jpg

245F7A6E-4181-46A0-8D35-F4B7007CFB53-5988-00000698969569F1.jpg

070FBC73-1E62-44F0-BCAE-EEE00D6A1BAD-326-000000426CEA1E90.jpg

 

 

 

Have a shit load more stuff but this will kick things off.

PM only for now

 

Cheers.

 

Have a spare 6-speed gearbox aswell + spare JDM headlights

Share this post


Link to post
Share on other sites

Set of 4 speedy Holo type r 17x7 +38 4x114.3 skid wheels.. Can come with tyres if needed $350 or $400 with 235/45r17 second handies

PM if interested

20130715_175641.jpg

Share this post


Link to post
Share on other sites

Wanted !!!!!!! Driving light switch for Xtrail, Navara or Pathfinder.

Here is a picture of the exact switch, Thanks.

auto-part-2012-nissan-new-x-trail-head-light-switch-nt-p-2086.jpg

Share this post


Link to post
Share on other sites

Its the Dads getting sick of my car sh*t in his garage sale.

There's plenty of stuff here that people might not even reuse, either way PM me if interested

 

2x T25 turbo's, lines attached. 1 was smoking. 1 has a little shaft play but no damage. Other is fine

1x Moroso SR20 oil sammich plate with AN-10 speedflow fittings, lines included to run oil cooler infront of s13 rad.

2x s13 knuckle bushings new

1x greddy turbro timer

1x response? sub, bought a while back was too slack to install

2x response? splits. installed but removed because race car

1x kenwood head unit with harness

1x s13 sr20 afm with plug

1x redtop sr20 flywheel with standard bolts

4x redtop standard pistons + rods. 2x mashed ringlands one one pison, running e85 so nice and clean still

1x 180sx hatch seal

3x random pod filters

2x sets of sr20 rocker arms

2x sr20 standard head gasket new

1x set standard SR20 redtop cams

1x brand new poncam with broken locating pin

1x 260 deg 12mm poncam

1x sr20 sump

2x an-8 lines

1x boost tee, new never installed. not sure of brand

1x sr20 timing chain, 2000km before I mashed ringlands

2x K&N HP 1002 oil filters, untouched in box (suit redtop SR)

 

also looking for an s13 'bent' style strut brace and type x kit.

 

some parts not listed, some stuff will end in bin if nobody needs.

SA northern suburbs

0419 382 447 or PM

photo.jpgphoto1.jpg

Hey Guys,

Most of this is still up for grabs, going to start chucking stuff soon. Give me offers, the worst I can say is no :)

Cheers

Share this post


Link to post
Share on other sites

350z rims. 3 with tyres 1 wrecked

$450

 

Rb25 forward facing plenum

$450

 

Rb25 with rod knock 400$

 

Share this post


Link to post
Share on other sites

R32 stainless rear cannon to rear flange $50

Turbosmart v port blow off $60

R32 Side skirts $60

Cusco strut brace r32 carbon fibre $90

Space save wheel r32 $30

R32 boot $70

Fmic $80

R32 Rear tail lights $100

Centre console $50 r32

Air flow meter $40 r32

Rb20 ignitor $50

Stock computer $40

Drivers side power window switch $40 r32

4runner bumper brand new 92 $100

T25 garret turbo good condition with stainless dump with inlet and outlet adapter $400

R32 grey bonnet with bonnet pin holes $100

18inch Full set starcorp rims swap for 18inch drift teks

Chasing a 50mm wastegate will swap for some

items

Edited by drmild

Share this post


Link to post
Share on other sites

4 x 225/50/16 Kumho KU-21 60% tread on all 4. Located northern suburbs, $100. PM me if you want them.

Share this post


Link to post
Share on other sites

Hey guys looking for a set of lmgt4s in 18 pref 8.5 and 9.5

Share this post


Link to post
Share on other sites

Wanted: type x tail light loom :)

I can make plug connections up but would rather keep it standard

Share this post


Link to post
Share on other sites

Wanting To Buy

high mount turbo package to suit SR20.

I'm After:

Turbo good for 320-380kws + braided lines to suit

High mount manifold + front and dump pipes

External wastegate

 

Also wanting Stage 2 Cams (BC Stage 2, Procams, HKS Step 2s etc)

 

SELLING

Work VS-XX 17x8 +11, 17x9 +22 4x114.3. Suits 180/s13 very well with -2 camber on front and none on rears. Gold centres + come with still cheapy roadworthy tyres (50-60%) 215/45 and 235/40 $1500 ono

 

Work Emotion XD9s Gunmetal Grey in like new condition 17x8.5 +17, 17x9.5 +17 4x114.3. Fits on rear with camber but suits cars with some guard roll, fronts need about -3 camber as well to fit. Tyres are Federal 595 SS 235/45 front and a thick 255/40 on the rears. These rims have no scratches or dents whatsoever, the stickers have faded a bit is all. $1800 ono

 

Low mount package to suit SR20

Kinugawa TD05 18G + braided lines to suit and single piece front+dump combo, currently making 280kw on 17psi and we did a run on 22psi which made 305kw. Can supply a tuned length Stainless Steel manifold for an extra $20 (has small crack on a weld which I assume can be fixed?) but I use the stock manifold for stealthiness. 3" metal intake pipe to suit Z32 AFM (AFM doesn't come with it) can be also be supplied for extra $50

 

$600 or $650 with metal intake pipe + tuned length manifold.

 

Tomei Poncams to suit SR20 non-vct 11.5mm lift and 256°IN/EX - Used and still in car but don't see why they wouldn't be in good condition- $350 (these will only be available after acquiring above high mount package)

Share this post


Link to post
Share on other sites

WTB - Looking for 180sx front passenger guard.

 

Must be straight, don't mind what colour or condition of paint as it will be needed to get resprayed anyways. Unless midnight type x purple.

Share this post


Link to post
Share on other sites

What a shitfight that was.... tidied.

Share this post


Link to post
Share on other sites

Aww man I always miss those.

Set of 18 8.5 x 9.5 black driftecks with toyo proxie r888 40 and 50% $1200

Share this post


Link to post
Share on other sites

I have an ATS 2way 4.3 ratio abs diff, 5 dolt drive shaft output. Excellent condition.

Wanting $750

 

S14a 5 speed gearbox. Been reconditioned and never used since as it was my spare box.

Wanting $650

 

S13 red top ecu with Nistune board.

Wanting $300

 

Sold the car so everything is clearing out. If you after something in particular, ask me but I'll try and have a huge list up in the next couple weeks.

 

Sms me for picks on 040959 seven zero four five.

 

Cheers.

Edited by NM35

Share this post


Link to post
Share on other sites

Wanted to buy

 

S14 Kouki rear wing and pods

 

S14 stainless cat back exhaust.

 

Text 0401 227 678

Share this post


Link to post
Share on other sites

Have stock 180 seats black sr trim $offer

Red 180 bonnet with pins $offer

 

0407793620

Edited by millerman

Share this post


Link to post
Share on other sites

Hey guys looking for a set of lmgt4s in 18 pref 8.5 and 9.5

 

These sizes just came up on FB with the JDM rims for sale Aus page, can look back and screenshot if you can't find the guy

Share this post


Link to post
Share on other sites

Hey guys looking for a set of lmgt4s in 18 pref 8.5 and 9.5

 

These sizes just came up on FB with the JDM rims for sale Aus page, can look back and screenshot if you can't find the guy

f you could that would be wonderful as im in syd atm far far away from my computer

Share this post


Link to post
Share on other sites

2x front S14 5 stud hubs (1 has studs missing) $50

S14 rear Stock camber. Traction arms $30

Rb26 fuel rail $40

S14 rear Tune agent camber arms $40

S14 Steering wheel airbag $40

Pmd fia 4 point harness. tags for 2015 $100

S14 Sunroof switches $10

S14 Rear seats $50

S14 Airbag module$20

Fc rx7 s5 front.rear bar. Front guards $90 each or $250 for the lot

S14 Weather shield. Passenger $50

S14 rocker cover $30

Greddy gauges ( has wiring, need senders) $100

S14 kick panel trims $20

RB25 intake manifold with throttlebody $50

S14 handbrake assy $20

S14 parcel shelf $20

r33 rb25 Cooler pipe with bov $20

Fc rx7 throttle body $40

fc rx7 Starter motor $30

fc rx7 Window switches $20

fc rx7 front Park lights . Indicators $20

Shit momo with boss $20

r32 skirts and door pods $200

all items located in ridgehaven, near TTP

price's negotiable, but be sensible

PM or contact 04 2 22 9 94 60

Edited by Tall Paul

Share this post


Link to post
Share on other sites

 

3/93

180sx

Factory redtop sr20det

300,000ks

Manual

NON HICAS

JIC Coilovers all round

Front strut brace

Factory style aftermarket intercooler

S15 front seats

Hks air filter

Turbo smart boot tee

SPL brain central 20 remapped computer

Lamco oil pressure,oil temp,boost and fuel pressure gauges

 

Paint on roof and bonnet is faded. Might come back with a polish.

Motor is pretty tired would suggest a freshen up of it.welsh plug leaks water..still drives fine..doesn't go That hard there is a bit of a miss.

Car has run out of rego.

 

Swaps only for other import.

Or clean luxury style car.

Or $4000 firm

 

image.jpg

image.jpg

image.jpg

image.jpg

Share this post


Link to post
Share on other sites

Z32 afm forsale, bought it brand new, used it twice, $250 Ono no plug

Share this post


Link to post
Share on other sites

WTB the following items, have cash waiting!

 

-S13 SR20DE Throttle position sensor

- 180sx front right guard in black and needs good paint

-180sx Bonnet in black, needs good paint

-180sx front bumper bar black

-180sx front reo bar

-S13 or 180 manual gear boot

-S13 or 180 kick panel that covers the ecu

-ca18det coilpack cover + screws

Share this post


Link to post
Share on other sites

WTB the following items, have cash waiting!

 

-S13 SR20DE Throttle position sensor

- 180sx front right guard in black and needs good paint

-180sx Bonnet in black, needs good paint

-180sx front bumper bar black

-180sx front reo bar

-S13 or 180 manual gear boot

-S13 or 180 kick panel that covers the ecu

-ca18det coilpack cover + screws

Got Rh guard but in white if you get stuck.

Share this post


Link to post
Share on other sites

WTB the following items, have cash waiting!

 

-S13 SR20DE Throttle position sensor

- 180sx front right guard in black and needs good paint

-180sx Bonnet in black, needs good paint

-180sx front bumper bar black

-180sx front reo bar

-S13 or 180 manual gear boot

-S13 or 180 kick panel that covers the ecu

-ca18det coilpack cover + screws

Got a S13/180sx Front reo bar UNCUT

-$60

 

post-16827-0-27517300-1374197982_thumb.jpg

Edited by thangLongz

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

×